SoftPlus Water Softeners Iron Rival Iron Reduction Systems ecoTAC Hard Water Conditioning Systems

1 Micron Melt Blown Polypropylene Sediment Cartridge for Watts Big Bubba®
Model #: BBC-150-D1 / PWWJCMB1

Watts Big Bubba 1 Micron Melt Blown Polypropylene Cartridge - #PWWJCMB1

MSRP: US$91.87
Our Price: US$76.56
You save: $15.31

- or -
Make us an offer for the Watts Big Bubba 1 Micron Melt Blown Polypropylene Cartridge -  #PWWJCMB1

Write a review.

Found a Lower Price?
Request a Price Beat
Free Shipping on orders over $79

Special Order Item.
Please contact us for lead time.

Watts Big Bubba 1 Micron Melt Blown Polypropylene Cartridge -  #PWWJCMB1

  • Description
  • Specifications
  • Related Products
  • Installation / Manual
  • Reviews

We are pleased to offer a complete selection of replacement cartridges for the Watts Big Bubba high flow housing. Watts Big Bubba melt blown polypropylene sediment cartridges are recommended when depth filtration is necessary for the reduction of soft particulate. PPWWJCMB1 melt blown polypropylene cartridges fit in Watts Big Bubba Filter Cartridge Housing.


  • Dual O-rings for superior sealing
  • 1 Micron filtration rating
  • Collects particles throughout the entire thickness of the filter
  • Greater efficiency with more surface area

#PWWJCMB1 1 Micron Melt Blown Polypropylene Sediment Cartridge Specifications

Technical Specifications
Model ##BBC-150-D1
Order #7100308
MediaMelt Blown Polypropylene
End capsPP + FG
Center tubesPoly Propylene
Maximum flow rate (GPM) 100
Maximum temperature 125°F (52°C)
Maximum°ΔP (psi) 40
Chemical resistanceExcellent
Length (media)26-1/4"
O-rings (dual)EPDM
Shipping weight (lbs.)5
Carton dimensions7" x 7" x 31"
Micron rating1
Note: Flow rates are based on each specific application, micron rating, solids content and a number of other factors. End user should consider these factors when selecting the filter housing (or number of filter housings) needed for their particular requirement.

Watts Big Bubba Housing

Watts Big Bubba Housing <br>Part#:BBH-150-NP<br><br>

MSRP: US$1,202.58
Our Price: US$1,002.15
You save: $200.43

- More Info -

Watts Big Bubba Carbon Cartridge
Model#: BBC-150-ACP

Watts Big Bubba Carbon Cartridge<br>Model#: BBC-150-ACP<br>Part#: PWWJCAC5<br><br>

MSRP: US$437.13
Our Price: US$364.28
You save: $72.85

- More Info -

Watts Big Bubba Carbon Block Cartridge
Model#: BB-C100

Watts Big Bubba Carbon Block Cartridge<br>Model#: BB-C100<br><br>

MSRP: US$679.92
Our Price: US$566.60
You save: $113.32

- More Info -

How to install a Watts Jumbo Big Bubba cartridge

  1. Close inlet valve.
  2. Close outlet valve.
  3. Open valve on drain, if a drainpipe has been installed.
  4. Press pressure relief button to relieve pressure.
  5. Remove lid after pressure has been relieved.
  6. Rotate cartridge counterclockwise and pull upward. Remove the cartridge.
  7. Install new cartridge. Push downward and rotate clockwise to engage locking tabs lubricating O-rings if necessary.
  8. Check lid O-ring to ensure it is properly seated. Lubricate if necessary.
  9. Replace lid.
  10. Replace eyebolts and tighten. (Hand tight is sufficient.)
  11. Close valve on drain if a drainpipe was installed.
  12. Open outlet pipe completely.
  13. Open inlet pipe slowly to check for leaks.
  14. Vent filter to dispel air by depressing pressure relief button. Be careful when relieving pressure

Watts Big Bubba 1 Micron Melt Blown Polypropylene Cartridge - #PWWJCMB1 Reviews

There are currently no reviews for this product.
Be the first to write a review.