Sterilight SSM-24 Ultraviolet (UV) Sterilizer
Sterilight Model SSM-24 Replacement Parts & Accessories
The Sterilight SSM-24 is well suited to point-of-use water treatment and post-RO disinfection, or for small cottages with maximum flow rate needs of 6.0 gallons per minute (22.7 LPM) to kill bacteria (including coliform and e.coli), viruses, cryptosporidium, giardia, and a wide range of other microbioogical contaminants. It is the most economical unit with this flow rate capcity that we offer that features a UV intensity monitor and a powered solenoid output. It is an excellent choice for applications with a known bacteria or other microbiliogical contamination problem.
Like all Sterilight Silver Plus Series UV water purifiers, the SSM-24 features a stainless steel reactor chamber, a fire-polished domed quartz sleeve, and Sterilight Sterilume™-EX coated low pressure germicidal UV lamp which can be conveniently changed without interrupting the water flow. The UV lamp provides a 4-log (99.99%) reduction of bacteria, viruses, and protozoan cysts (cryptosporidium and giardia) at the specified maximum flow rates. Lamp life is 9,000 hours (1 year). The SSM-24 uses Sterilight's electronic "ICE" controller features a switchable power supply that automatically detects line voltage between 100-240 volt and adjusts its operating settings accordingly. It also features a convenient display which indicates % UV output, remaining lamp life, and total days of operation. Coupled with a true 254nm UV intensity monitor housed in a stainless steel enclosure, the controller continuously monitors the UV output and warns you of any changes in water quality or if the water becomes unsafe to drink. The SSM-24 also comes with a powered solenoid output that allows you to connect an emergency solenoid valve shut-off kit (sold separately) directly into the controller. See below for more information.
All UV sterilizers required sediment pre-filtration to reduce or eliminate the possibility that a targeted contaminant could "hide" behind a sediment particle in the "shadow" of the UV light and therefore not receive a full dose of UV light. Accordingly, the manufacturer strongly recommends sediment pre-filtration down to a level of 5 microns or smaller.
Water exceeding 120 ppm in hardness (7 grains per gallon) should be softened to reduce the risk that hard water mineral scale will build-up on the UV sleeve thereby reducing UV light distribution into the UV chamber. Similarly, iron levels exceeding 0.3 ppm or manganese levels exceeding 0.05 ppm should also be treated to prevent staining of the UV sleeve.
Elevated levels of certain other contaminants, such as tannins, can cause a reduction in UV transmittance (the ability of the water to transmit UV light). If the UV transmittance (UVT) of your water is less than 75% after the above-mentioned pre-treatment, activated carbon filtration may be desirable to improve UV transmittance. The majority of deep wells have a UVT of 85% or greater. If your UVT is unknown, select a model with a higher flow rate capacity then you feel you will really require (this will provide a higher UV dose at your desired flow rate), or add an activated carbon pre-filter to your system. We recommend the following pre-filter equipment:
|Sterilight SSM-24 Specifications|
|Max. Flow Rate
(UV dose >30 mJ/cm2)*
|6 GPM (23 LPG)|
|Max. Flow Rate
(UV dose >40 mJ/cm2)*
|4.5 GPM (17 LPM)|
|Water Chamber Material||304 Stainless Steel|
|Chamber Length||22.1 inches / 56.1 cm|
|Chamber Diameter||2.6 inches / 6.5 cm|
|Controller Size||8.3 x 3.2 x 2.5 inches
(21.1 x 8.1 x 6.4 cm)
|Power Consumption||26 watts|
|Lamp Power||24 watts|
|Inlet / Outlet Plumbing Ports||3/4" MNPT|
|"Power-On" Indicator Light|
|Audible Lamp Failure Alarm|
|Lamp Replacement Reminder|
|LED Display: Lamp Life Remaining, Total Controller Runtime, UV Intensity|
|UV Intensity Monitor|
|Powered Solenoid Output|
|Warranty||Reaction Chamber: 7 years
Lamp: 1 year
All Other components:2 years
*Note: Maximum recommended flow rates based on 95% UV transmittance. Actual dosage depends on flow rate, water quality, and maintenance (cleaning ov UV sleeve). UV dosage will be lower when the UV transmittance capacity of the water drops below 95% - if in doubt, select a model rated for a higher flow rate than you actually require. We recommend a UV dose of 40 mJ/cm2.
|Feed Water Quality Parameters|
|Iron||0.3 ppm (0.3 mg/L)|
|Manganese||0.05 ppm (0.05 mg/L)|
|Tannins||0.1 ppm (0.1 mg/L)|
|Turbidity||< 1 NTU|
|Hardness||< 120 ppm (7 grains / gallon)|
|UV Transmittance (UVT):||75%|
|Maximum Temperature:||104F (40C)|
|Maximum Pressure:||125 psi|