CAD / USD
CART
1-866-376-2690
SoftPlus Water Softeners Iron Rival Iron Reduction Systems ecoTAC Hard Water Conditioning Systems Black Friday Sale

Dow Filmtec SW30HRLE-400i Reverse Osmosis (RO) Membrane

replacement 7,500 GPD seawater desalination reverse osmosis (RO) membrane element

The Filmtec SW30HR LE-400i element offers a combination of high rejection and low energy requirements to allow lower total costs with medium and high salinity feedwater. Filmtec SW30HR LE-400i element comes with the distinct iLEC(tm) Interlocking Endcaps that help reduce system operating costs and reduce the risk of o-ring leaks that cause poor water quality. Benefits of the Filmtec SW30HR LE-400i element include:

  • Enables systems to be designed and operated to optimize operating cost through lower energy consumption or to optimize capital cost through higher productivity at lower operating fluxes.
  • High NaCl and boron rejection to help meet World Health Organization (WHO) and other drinking water standards.
  • Effective use in permeate staged seawater desalination systems without impairing the performance of the downstream stage.
  • High performance over the operating lifetime without the use of oxidative post-treatments. This is one reason Filmtec elements are more durable and may be cleaned more effectively over a wider pH range (1-13) than other RO elements.
  • Automated, precision fabrication with a greater number of shorter membrane leaves reducing the effect of overall fouling and maximizing element efficiency, helping to lower your cost of operation.
Specifications:
Membrane Type:Polyamide Thin-Film Composite (TFC)
Maximum Operating Temperature:113F (45C)
Maximum Operating Pressure:1,200 psi (83 bar)
Maximum Pressure Drop:13 psi (0.9 bar)
pH Range, Continuous Operation:2-11***
pH Range, Short-Term Cleaning:1-13* (30min)
Maximum Feed Silt Density Index:5 SDI
Free Chlorine Tolerance:<0.1 ppm**
Permeate Flow Rate:7,500 GPD (28 m3/day)*
Stabilized Salt Rejection:99.75%
Minimum Salt Rejection:99.6%
Stabilized Boron Rejection:91%
Feed Spacer:28 mil
Filmtec SW30HRLE-400i Reverse Osmosis (RO) Membrane

*The above benchmark values are based on the following test conditions: 32,000 ppm NaCl, 800 psi (5.5 MPa), 77F (25C), pH 8 and 8% recovery. Permeate flows for individual elements may vary +/-15%.

**Under certain conditions, the presence of free chlorine and other oxidizing agents will cause premature membrane failure. Since oxidation damage is not covered under warranty, Dow recommends removing residual free chlorine by pretreatment prior to membrane exposure. Most RO systems have carbon pre-filters for this purpose.

***Maximum temperature for continuous operation above pH 10 is 95F (35C).

Note: Active surface area guaranteed +/-5%. Active area as stated by FilmTec is not comparable to nominal membrane area often stated by some manufacturers.

Dimensions:

   A: 40.0" (1,016mm)
   B: 40.5" (1,029mm)
   C: 7.9" (201mm)
   D: 1.125"ID (29mm)
Filmtec SW30HRLE-400i Size Chart

Element fits nominal 8-inch (203 mm) I.D. pressure vessels. Individual iLEC elements measure 40.5 inches (1,029 mm) in length (B). The net length (A) of iLEC elements when connected is 40 inches (1,016 mm).

Model Diameter Inches Length Inches Active Surface
Area ft2 (m2)
Test Pressure Permeate Flow
Capacity
GPD (m3/day)
Price
(w/ Free Shipping)
Filmtec SW30HRLE-400i
Our Stock #703246512
Dow Part #246512
8 40 400 (37) 800 psi 7,500 (28)
List Price: CDN$2,838.00
Price: CDN$1,669.00
You save: $1,169.00


Write a review.

Notice: The use of this product in and of itself does not necessarily guarantee the removal of cysts and pathogens from water. Effective cyst and pathogen reduction is dependent on the complete system design and on the operation and maintenance of the system.

Customer Questions & Answers


No customer questions have been submitted for this. Have a question? Ask it above.