Sterilight Platinum SPV Series
NSF-Certified Ultraviolet (UV) Water Purifiers

Sterilight Platinum NSF-Certified (SPV) Series UV Water Purifier The Sterilight Platinum NSF-Validated SPV Series was designed for whole house and light commercial applications with water flow rates up to almost 15 gallons per minute (multiple units in parallel can be used for even higher flow rates). Applications include private wells and lake water supplies, camp grounds, hotels, bottlers, aquaculture, hospitals, food, cottages, restaurants, breweries, water systems, laboratories, marine, pharmaceutical, dairies and more. All Sterlight Platinum SPV Series models are independently certified by NSF (NSF/ANSI Standard 55 Class A Validation).

In addition to carrying NSF-certification, the Platinum SPV Series is loaded with features typically found in only expensive commercial units, yet it is available at a very economical price - in fact, many models cost considerably less than competitors' models with far fewer features! The Sterilight SPV Series is very economically priced compared to comparable NSF-certified models from other manufacturers.

The Sterilight Platinum SPV Series is based on the feature-laden Platinum™ ICE controller and Sterilight's Flow-Pace™ UV intensity monitor. This combination allows for 2-stage flow pacing where the lamps operate at half power when water is not flowing and full-power when the water is running. This allows the system to operate with minimal power requirements (excellent for applications powered by solar power systems!), at a lower operating cost, and with less heat build-up. The Platinum™ ICE controller provides constant output current and a universal power input (100-250V/50-60Hz), as well as visually displaying % UV intensity, remaining lamp life, and total hours of operation. The system comes with a set of dry contacts allowing for the external hook-up of a remote device such as a solenoid valve (sold separately - see below), as well as a self-diagnostic check upon start-up, and an RJ-11 communications port. Using high-output, Sterilume™-HO coated low pressure germicidal UV lamps coupled with electropolished 316 stainless steel, axial flow sterilization chambers, the Platinum SPV Series provides very high flow throughput capacity in a very compact system. The UV lamp provides a 4-log (99.99%) reduction of bacteria, viruses, and protozoan cysts (cryptosporidium and giardia) at the specified maximum flow rates. Lamp life is 9,000 hours (1 year). A suitable flow restrictor is also included to ensure that you do not exceed the maximum recommended UV dose.

The Sterilight Platinum SPV Series is composed of five models with treatment capacities up to 14.9 gallons per minute.





Sterilight
SPV-200
Sterilight
SPV-410
Sterilight
SPV-600
Sterilight
SPV-740
Sterilight
SPV-950
Applications point of use
small commercial
small home
cabin
small commercial
average home
small commercial
most homes
small commercial
large home
commercial
Max. Flow Rate
(UV dose >40 mJ/cm2 at 75% UVT)
2.6 GPM
(10 LPM)
5.9 GPM
(22 LPM)
8.6 GPM
(32 LPM)
11.2 GPM
(43 LPM)
14.9 GPM
(56 LPM)
Water Chamber Material Electropolished 316 Stainless Steel
Chamber Length 17.8" /
45.2 cm
26.0" /
66.0 cm
30.7" /
78.0 cm
39.4" /
100.1 cm
44.5" /
113.0 cm
Chamber Diameter 3.5 inches / 8.9 cm
Controller Size 11 x 4.5 x 2.0 inches / 25.4 x 11.4 x 5.3 cm
Lamp Type Sterilume-HO Series
Lamp Model S200RL-HO S410RL-HO S600RL-HO S740RL-HO S950RL-HO
Sleeve Quartz
# QS-200
Quartz
# QS-410
Quartz
# QS-600
Quartz
# QS-740
Quartz
# QS-950
Electrical 100-240v, 50/60HZ
Power Consumption 35 watts 52 watts 73 watts 88 watts 110 watts
Lamp Power 30 watts 45 watts 65 watts 80 watts 100 watts
Inlet / Outlet Plumbing Ports 1/2" MNPT Combo 3/4" FNPT / 1" MNPT
"Power-On" Indicator Light
Audible Lamp Failure Alarm
Lamp Replacement Reminder
LED Display: Lamp Life Remaining, Total Controller Runtime, UV Intensity
UV Intensity Monitor
Powered Solenoid
Output
Flow Pacing
Communications Port
Diagnostic Check
Flow Restrictor
NSF-Certification
NSF/ANSI Standard 55 Class A




Sterilight
SPV-200
Sterilight
SPV-410
Sterilight
SPV-600
Sterilight
SPV-740
Sterilight
SPV-950
Price
Switch to CDN pricing
Discontinued
See Viqua PRO 10 for replacement
Discontinued
See Viqua PRO 10 for replacement
Discontinued
See Viqua PRO 10 for replacement
Discontinued
See Viqua PRO 10 for replacement
Discontinued
See Viqua PRO 20 for replacement
Feed Water Quality Parameters
Iron 0.3 ppm (0.3 mg/L)
Manganese 0.05 ppm (0.05 mg/L)
Tannins 0.1 ppm (0.1 mg/L)
Turbidity < 1 NTU
Hardness < 120 ppm (7 grains / gallon)
UV Transmittance (UVT): 75%
Maximum Temperature: 104F (40C)
Maximum Pressure: 125 psi

Pre-treatment Requirements:

All UV sterilizers required sediment pre-filtration to reduce or eliminate the possibility that a targeted contaminant could "hide" behind a sediment particle in the "shadow" of the UV light and therefore not receive a full dose of UV light. Accordingly, the manufacturer strongly recommends sediment pre-filtration down to a level of 5 microns or smaller.

Water exceeding 120 ppm in hardness (7 grains per gallon) should be softened to reduce the risk that hard water mineral scale will build-up on the UV sleeve thereby reducing UV light distribution into the UV chamber. Similarly, iron levels exceeding 0.3 ppm or manganese levels exceeding 0.05 ppm should also be treated to prevent staining of the UV sleeve.

Elevated levels of certain other contaminants, such as tannins, can cause a reduction in UV transmittance (the ability of the water to transmit UV light). If the UV transmittance (UVT) of your water is less than 75% after the above-mentioned pre-treatment, activated carbon filtration may be desirable to improve UV transmittance. The majority of deep wells have a UVT of 85% or greater. If your UVT is unknown, select a model with a higher flow rate capacity then you feel you will really require (this will provide a higher UV dose at your desired flow rate), or add an activated carbon pre-filter to your system. We recommend the following pre-filter equipment:

sediment pre-filter for UV sterilizer sediment and activated carbon pre-filter for UV system iron reduction filter
WH1B+
5 Micron Sediment
Pre-Filter Package


excellent overall sediment pre-treatment to 5 micron level
WH2
Sediment & Activated
Carbon Pre-Filter Package


sediment pre-treatment to 5 microns and improves UV transmittance by removing tannins and other contaminants that reduce UVT
WH5
Iron Reduction
Filter Package


very cost effective iron pre-treatment filter for iron levels ranging from 0.3 to 5.0 ppm

Accessories:

The Sterilight Platinum SPV series can be equipped with an emergency solenoid shut-off kit. In the event of a power failure or electrical outage to your home, your UV lamp in your UV system will lose power. This could leave your home unprotected if someone turns on a water faucet. Some bacteria and other waterborne pathogens can also swim past an un-powered UV lamp and reach the downstream portion of your water system and therefore not receive a dose of UV light once the power is restored. The same situation could occur in the event of a UV bulb failure or in the event of a reduction in UV lamp output (drop in UV intensity below safe dosage level). The solenoid emergency shut-off valve is normally installed at the output of your UV system and will physically close a valve in the event of a bulb burn-out or power failure, thereby preventing any contaminant from passing through the system untreated. This feature will also turn off the water supply if there is a UV intensity loss (for models equipped with a UV intensity monitor). This kit is highly recommend for all homes with a known bacterial, virus, or cyst contamination problem, and for all homes with an electrical supply that is prone to frequent outages. Various valve sizes are available. For more details, review our Sterilight solenoid valve kits page.